In The Antenna Selection Of On-board UAV Suppressors, The Interference Effect, Scene Adaptability, Installation Convenience And Regulatory Compliance Need To Be Considered Comprehensively.The Following Are The Key Selection Points And Suggestions

Mar 02, 2025 Leave a message

In the antenna selection of on-board UAV suppressors, the interference effect, scene adaptability, installation convenience and regulatory compliance need to be considered comprehensively.The following are the key selection points and suggestions: --- ###**1. Antenna type selection: directional antennavsomnidirectional antenna** 1. **Directional antenna** -**Advantages**: -**Long interference distance**: The effective shielding distance in the direction of the main lobe is significantly increased, which is suitable for targeted interference needs (such as tracking drones in a specific direction).-**Reduce accidental injuries**: Reduce the impact on non-target areas (such as surrounding communication base stations) by concentrating energy and directional interference. -**Disadvantages**: -**Large size and wind resistance**: It is usually a plate-like structure, and the wind resistance is obvious when driving at high speed, so the installation and fixing design needs to be strengthened. -**Low flexibility**: The direction needs to be adjusted manually, which is not suitable for fast movement or multi-target scenes.2. **Omnidirectional antenna** -**Advantages**: -**All-round coverage**: No need to adjust the direction, suitable for all-round defense in open areas (such as airports and squares).-**Easy to install**: Mostly upright rod-shaped structure, small size, suitable for rapid deployment on-board. -**Disadvantages**: -**Short interference distance**: The effective range of the same power is less than that of the directional antenna, and the power or quantity may need to be increased to make up for it. **Scene adaptation recommendations**: -**Directional antenna**: Suitable for scenarios where precise strikes are required and the mission area is clear (such as border patrol, protection of important facilities).-**Omnidirectional antenna**: Suitable for temporary urban activities, mobile patrols and other scenes that require fast response and wide coverage. --- ###**2. Core performance parameters** 1. **Frequency band coverage capability** -Must cover the frequency band commonly used by drones: -**Communication frequency band**: 2.4GHz, 5.8GHz (remote control and image transmission). -**Navigation frequency band**: GPSL1 (1.575GHz), Beidou B1 (1.561GHz), GLONASS, etc. -Support independent control of multiple frequency bandstoavoid interference from all frequency bands affecting legitimate equipment. 2. **Gain and power** -**Gain**: High-gain antennas can enhance the interference intensity. For example, the gain of directional antennas is usually 8-10dB, and omnidirectional antennas are about 3-5dB. -**Power**: On-board equipment often requiresmore than 100W radio frequency powerto ensure effective suppression of drone signals, but it must comply with national radio management standards.3. **Response speed and stability** -Support fast switching of interference modes (forced landing, eviction), and the response time should be ≤3 seconds. -Thermal design (such as liquid cooling, heat pipe cooling) and overload protection are required to adapt to long-term operation. --- ###**3. Installation and environmental adaptability** 1. **Installation method** -**Magnetic or suction cup fixed**: Easy to deploy quickly, suitable for temporary tasks (such as the magnetic gain antenna mentioned on Page 7). -**Roof or bumper installation**: Priority is given to low wind resistance designto avoid falling off or damage when driving at high speed. 2. **Environmental tolerance** -**Protection level**: At leastIP65 (dustproof and waterproof), suitable for rainy days or sand and dust environments.-**Temperature range**: It needs to supportthe operating temperature of -20℃~60℃toadapt to extreme climates in the wild. --- ###**4. Compliance and security** 1. **Regulatory certification** -Domestic equipment must pass the National Radio Monitoring Center testing (SRRCcertification), and export equipment must comply with FCC/CE standards. -Avoid using unauthenticated"three No"productsto prevent legal risks.2. **Directional and precise interference** -Combined with beamforming technology, the interference range is reduced and the accidental injury to non-target equipment is reduced. --- ###**5. Brand and technical support** -Give priority to manufacturers with military background or mature cases (such as Shenzhen Huaxin and Nanjing Baikang) to ensure technical reliability and after-sales support. -Some manufacturers provide customized services, and antenna parameters (such as frequency band expansion and gain optimization) can be adjusted according to demand. --- ###**Summary recommended plan** 1. **Urban patrol/temporary tasks**: Lightweight omnidirectional antenna (such as shark fin shape), taking into account concealment and fast response.2. **Military/border defense**: High-power directional antennas (such as Yagi antennas or logarithmic periodic antennas), with integrated detection-interference systems.3. **Complex electromagnetic environment**: Multi-band coverage + high-gain combined antenna, combined with intelligent filtering technology to reduce interference. When choosing, you need to weigh interference performance, installation restrictions and regulatory requirements. It is recommended to verify the antenna performance through actual measurements before deploying in batches.